Metal Protection Solutions

High-performance functional coatings that protect metal surfaces from moderate to severe environmental and industrial conditions including high temperatures, corrosion, and chemical exposure.

Functional coating solutions geared towards protecting structural integrity and preventing loss of lives

45-DC Polyurea

VersaFlex USA

A fast set, rapid curing, 100% solids, flexible, two-component polyurea elastomeric spray coating. Produces an extremely tough film at all thicknesses, will not hydrolyze, leach or contaminate other materials, and is bondable and paintable.

  • Low permeation & excellent thermal stability 
  • Direct food contact approved
  • 100% solids, no VOC’s
  • Tough elastomeric membrane 
  • Minimal downtime

Typical Applications:

It can be used in transitional areas along with interior or exterior applications. Below & above-grade waterproofing, water & wastewater treatment, food processing facilities, pulp & paper mills, parking garage decks, bottling & canning facilities.

Substrate:

Concrete

Type of Product:

Top Coat

Categories:

  • Concrete Protection System
  • Engineering Product Range

9100 System DTM Epoxy Mastic

Rust-Oleum, USA

A two-component, high solids epoxy coating for use in moderate to severe environments.

It is specifically designed for application directly on sound rusted steel with minimum surface preparation.

  • Direct-to-metal
  • Self-priming formula
  • Excellent resistance – chemicals, abrasions, impact, and solvent Meet incidental food contact requirements.

Typical Applications:

It can be used on clean and sound rusted steel, concrete (including concrete floors), previously coated and slightly damp surfaces. It may also use for water immersion. Service, Chemical plants, steel structures, pre-treated buildings, pipes, etc.

Substrate:

Concrete / Metal

Type of Product:

Primer / Top Coat

Categories:

  • Metal Protection System
  • Engineering Product Range

C-200 – Coaltar Epoxy Finish

Kan-Tar

A high solid, polyamide-converted epoxy that includes refined coaltar pitch, which forms an extremely durable coating. It is recommended for both new construction and maintenance in moderate to severe chemical, marine, and atmospheric exposures.

  • Excellent abrasive strength
  • Strong chemical resistivity
  • Water-resistant barrier
  • Excellent corrosion resistance
  • Self-priming high build coating

Typical Applications:

Tubular steel pilings wharf structures, bridge undersides, and dams buried pipelines.

Substrate:

Metal/Masonry

Type of Product:

Top Coat

Categories:

  • Metal Protection System
  • Engineering Product Range

Chlorinated Rubber Finish

Based on unmodified chlorinated rubber resin. When used in combination with suitable primer, the system exhibits exceptional water Impermeability, resistance to salt spray, spillage & fumes of most acids, salt solutions, alkalis, bleaching agents, and corrosive gases.

  • Excellent chemical resistance
  • Single pack product
  • Resistance to molds and fungal growth 
  • Recoatable

Typical Applications:

Fertilizer plants, plating shops, paper mills, breweries, exterior coatings on chemical storage tanks, and in the mining industry.

Substrate:

Concrete / Metal

Type of Product:

Top Coat / Chlorinated Rubber

Categories:

  • Metal Protection System
  • Engineering Product Range

Chlorinated Rubber Primer

Kan-Tar

Based on unmodified chlorinated rubber resin. When used in combination with KAN- Cor CR finish, the coating system exhibits exceptional water impermeability, resistance to salt spray, spillage and fumes of most acids, salt solutions, alkalis, bleaching agents, and corrosive gases.

  • Excellent water impermeability 
  • Salt spray resistance
  • Withstands fumes and splashes of most acids 
  • Resist alkalis & other chemicals
  • Easy to recoat 

Typical Applications:

Concrete, plaster, and masonry surfaces, fertilizer plants, plating shops, and gas works.

Substrate:

Concrete / Metal

Type of Product:

Primer

Categories:

  • Metal Protection System
  • Engineering Product Range

Epoxy High Build Liner

KAN-Thor

This is a two component amine cured epoxy coating. It is a high built product, designed to

Improve barrier protection as a mid-coat (intermediate) / topcoat in systems for various

Atmospheric conditions. It can be used as a liner for the storage of various products.

  • High Build
  • Strong chemical resistivity 
  • High abrasion resistant

Typical Applications:

Steel structures, inner surfaces of storage tanks, and equipment in chemical exposure.

Substrate:

Metal

Type of Product:

Intermediate Coat & Liners (Amine Cured)

Categories:

  • Metal Protection System
  • Engineering Product Range

Etch Primer

Kan-Etch

A two-pack polyvinyl butyl based primer which contains zinc tetroxide chromate as the

Passivation pigment. It is recommended as an adhesion-inducing primer for use on non-ferrous metals.

  • Simple mixing ratio 1:1
  • Good adhesion – minimum surface preparation Matt finish
  • Non-toxic

Typical Applications:

Corrugated sheets makeshift shelters and steel structures.

Substrate:

Galvanized Metal / Aluminium

Type of Product:

Primer for Non-FerrousMetals

Categories:

  • Metal Protection System
  • Engineering Product Range

Ethyl Zinc Silicate Primer

Kan-Therma

A two-component moisture-cured primer recommended using as a primer coat underneath specified topcoats in the most aggressive industrial and marine environments.

  • Excellent heat resistant property
  • Good resistance to abrasion
  • Weather-resistant
  • Good resistance to moisture 
  • Easy application
  • Temperature resistance 400-C

Typical Applications:

Bridge structures and exteriors of petroleum storage tanks, marine installations, offshore platforms, and high-temperature environments.

Substrate:

Metal

Type of Product:

Primer / Inorganic Silicate

Categories:

  • Metal Protection System
  • Engineering Product Range

Heat Resistant (Aluminium) – 200OC

KAN- Therma

A single pack heat-resistant general-purpose finish pigmented with/without aluminum flake. Designed to be a heat resistant coating for primed steel structure subject to temperature up to 200°C.

  • Excellent heat resistant property
  • Good resistance to abrasion
  • Weather-resistant
  • Good resistance to moisture 
  • Easy Application

Typical Applications:

Tank farms, muffles, chimneys, and general structural steelwork pipelines where there is a high-temperature work environment.

Substrate:

Metal

Type of Product:

Top Coat (High Heat Resistant)

Categories:

  • Metal Protection System
  • Engineering Product Range

Heat Resistant (Silicone) – 450OC

Kan-Therma

A metallic flake-filled finish based on a highly durable silicone medium designed to give excellent resistance to heat and weathering. The finish also provides maximum brilliance and reflective properties.

  • High heat resistance 
  • Anti-corrosive
  • Silicone-based

Typical Applications:

Tank farms, muffles, chimneys, and general structural steelwork pipelines where there is a high-temperature work environment.

Substrate:

Metal, Galvanized steel

Type of Product:

Top Coat (Silicon)

Categories:

  • Metal Protection System
  • Engineering Product Range

Heat Resistant (Silicone) – 650OC

KAN- Therma

A metallic flake-filled finish based on a highly durable silicone medium designed to give excellent resistance to heat and weathering. The finish also provides maximum brilliance and reflective properties.

  • Good moisture resistance 
  • Anti-corrosive properties 
  • Excellent Weatherability
  • Reflective properties
  • High heat resistance

Typical Applications:

Tank farms, muffles, chimneys, and general structural steelwork pipelines where there is a high-temperature work-environment severe condition. 

Substrate:

 Metal / Galvanized Steel

Type of Product:

Top Coat (Silicone-Based)

Categories:

  • Metal Protection System
  • Engineering Product Range

Heat Resistant (Zinc Dust Graphite)

Kan-Therma

A two-pack product based on graphite, incorporating zinc dust. It is designed for steel surfaces operating in the temperature range from 150oC – to 450oC.

  • Excellent weatherability
  • Resists rain and condensation
  • Fair resistance to aliphatic solvents 
  • Non-toxic dry film

Typical Applications:

Tank farms, muffles, chimneys, and general structural steelwork pipelines where there is a high-temperature work environment. 

Substrate:

Metal

Type of Product:

Top Coat

Categories:

  • Metal Protection System
  • Engineering Product Range

High Build Epoxy Finish

KAN-Taurus

A high build, two components epoxy coating is a versatile original and maintenance coating for machinery, steel structures, and marine installations.

  • Moderate chemical resistivity 
  • Excellent Abrasion 
  • Resistivity High build

Typical Applications:

MS structure and tank, fertilizer plants, chemical units, refineries, petrochemicals, etc.

Substrate:

 Metal  

Type of Product:

Top Coat 

Categories:

  • Metal Protection System
  • Engineering Product Range

High Build Zinc Phosphate Epoxy Primer

Kan-Taurus

Hi-build two components general-purpose industrial primer that contains Zinc Phosphate for corrosion inhibition. It is recommended as the standard heavy-duty primer for suitably prepared steel surfaces.

  • Non-toxic
  • Strong corrosion resistivity
  • Excellent chemical resistance 
  • Solvent resistant
  • Hi-Build

Typical Applications:

General maintenance tank, storage facilities, cranes, and process plants.

Substrate:

Metal

Type of Product:

Primer / Epoxy

Categories:

  • Metal Protection System
  • Engineering Product Range

MIO Epoxy Finish

KAN-Taurus

A two-component polyamide cured epoxy coating with Micaceous Iron Oxide pigmentation, displays outstanding durability and abrasion resistance. It is used as an intermediate coat in many coating systems.

  • Hi-build
  • Resists early scale UV degradation 
  • High Abrasion resistance
  • Excellent water/saltwater resistance

Typical Applications:

Steel structures, wharf super-structures, high transmission towers, ship loaders, hoppers, conveyors, silos and storage tanks & other marine structures.

Substrate:

 Metal  

Type of Product:

Intermediate Coat

Categories:

  • Metal Protection System
  • Engineering Product Range

Noxyde

Rust-Oleum, USA

A single component, rust preventative water-based acrylic elastomeric coating. This self-priming, high build coating is designed for minimally prepared sound rusted or clean steel in mild to moderate industrial environments.

  • High-performance product
  • Self-Priming
  • Unrivalled corrosion protection 
  • 200% elasticity
  • Protects against cracking & peeling 
  • UV resistant
  • Fulfils the requirement for corrosively class C5 (M) high as defined by ISO standard 12944

Typical Applications:

Iron, steel, special alloys, galvanized and metalized iron, and steel.

Substrate:

Concrete / Metal

Type of Product:

Primer / Top Coat

Categories:

  • Metal Protection System
  • Engineering Product Range

Polyurethane Finish

Kan-Supra

Good chemical resistant and is particularly suitable for surfaces where high durability is required. It is a versatile coating with excellent gloss retention and UV resistance.

  • Excellent weatherability 
  • Easy application
  • Excellent gloss and colour retention 
  • UV resistant
  • Tough and abrasion-resistant
  • Good chemical resistivity and durability 

Typical Applications:

Offshore structures, chemical and petrochemical plants, and bridges.

Substrate:

Metal / Wood / Concrete / Plastic

Type of Product:

Top Coat (Gloss, Satin, Matt)

Red Oxide Primer (Alkyd)

Kan-Alko

An alkyd-based primer is used for the protection of prepared steel surfaces in mild industrial or commercial environments.

  • Matt finish
  • Single component 
  • Fast dry
  • Anti-corrosive properties 

Typical Applications:

Structural steel, piping, cranes, building frames, bridges, towers, and tanks. It is also used in pulp and paper mills, the power industry as well as prefabricated structures and roofing.

Substrate:

Metal

Type of Product:

Primer (Alkyd Systems)

Categories:

  • Metal Protection System
  • Engineering Product Range

Synthetic Enamel

Kan-Alko

Synthetic Enamel is a tough, enamelled gloss finish based on durable alkyd resins and provides good durability and weathering resistance in mild industrial environments.

  • Good weatherability
  • Attractive glossy finish
  • Anti-corrosion properties 
  • Multiple colour options For Interior / Exterior use 

Typical Applications:

General maintenance

Substrate:

 Metal/Wood

Type of Product:

Top Coat / Alkyd based

Categories:

  • Metal Protection System
  • Engineering Product Range